### Contact Form

### Rate analysis for RCC slab m20 - calculate quantity & cost ...

Quantity of cement = 1/5.5 × 15.4 m3 × 1440 kg/m3 = 4032 kg, no of bag cement for 10m3 rcc slab 1:1.5:3 (m20) = 4032/50 = 80.64. If rate of cement = INR 350 per bag, then cost of 80.64 bags cement = 80.64×350 = INR 28224. step 3, Sand quantity :- generally sand measured in CFT and 1m3 = 35.3147.

Learn More### IS-10262-2009-CONCRETE MIX DESIGN - INDIAN STANDARD …

### Concrete Mix Design As Per Indian Standard Code

IS 456-2000 has designated the concrete mixes into a number of grades as M10, M15, M20, M25, M30, M35 and M40. In this designation the letter M refers to the mix and the number to the specified 28 day cube strength of mix in N/mm 2. The mixes of grades M10, M15, M20 and M25 correspond approximately to the mix proportions (1:3:6), (1:2:4), (1:1 ...

Learn More### Rate Analysis Of Concrete - M25 Concrete Example Rate Analysis

### Concrete Slump Test for Workability -Procedure and Results

2/15/2016 · Remove the excess concrete and level the surface with a trowel. Clean away the mortar or water leaked out between the mould and the base plate. Raise the mould from the concrete immediately and slowly in vertical direction. Measure the slump as the difference between the height of the mould and that of height point of the specimen being tested.

Learn More### Reinforced Concrete Analysis and Design

9/2/2011 · Design of Reinforced Concrete Beams 2.0 NOTATION min max Compression face to point on surface of concrete Where crack width is calculated Centre-to-centre distance between bars or groups of bars Point on surface of concrete to nearest face of a bar Gross area of concrete in a section

Learn More### Compressive Strength of Concrete | Cube Test, Procedure ...

5/18/2018 · As we assumed M20 grade concrete mix which bear a max load upto 20N/mm². Minimum Strength to be achieved at different days: 65% @7 days: 90% @14 days: 99% @28 days: Percentage of Concrete gain (test results) (13.7x100)/20 = 68.5%>65% (18.13x100)/20 = …

Learn More### CE2401-DESIGN OF REINFORCED CONCRETE AND BRICK …

The Coefficient of friction between base slab and concrete=0.55 Adopt M20 grade concrete and Fe415 grade steel. 9. a) What are the design principles involved in the different components of counterfort retaining wall. b) Write down the steps involved in the design of counterfort retaining wall. 10.

Learn More### Top 60 Civil Engineering Interview Questions And Answers Pdf

10/11/2020 · steps involved in the concreting process are : 1. Batching 2. Mixing 3. Transporting and placing of concrete 4. Compacting. Q.4) What are the Nominal Concrete Mix proportions for different grades? Nominal mix concrete used for concrete of M-20 or lower. M5- 1:5:10, M7.5- 1:4:8, M15- …

Learn More### Step by step method to Construct RC Residential House in ...

In this article, we are going to discuss how to construct an RCC residential house in India. This will be very useful for entry-level engineers or anyone who wants to understand the different process and steps involved in the construction of the house in India.

Learn More### UNIT-I DESIGN CONCEPTS, DESIGN OF BEAMS Part - A (Short ...

shear stress at the support. Use M20 concrete and Fe 250 steel. 4 A singly reinforced concrete beam is 400x450 mm deep to the centre of tension reinforcement which consists of 4 bars of 16mm diameter. If the safe stresses on concrete and steel are 7 N / mm2 and 230 N / mm2 respectively, find the moment of resistance of the section.

Learn More### (PDF) Concrete Mix Design By Packing Density Method

9/30/2020 · Large number of trial casting were carried out for each grade of concrete (i.e., M20, M25, M30, M35 and M40) with different water cement ratio and three paste contents in excess of void content.

Learn More### Reinforced Concrete Quantity and Rate Analysis | Civil ...

In order to perform rate analysis for reinforced concrete, two steps are involved: 1- Estimation of number of labour and equipment, quantity of materials, miscellaneous items required for for a certain quantity of reinforced concrete. 2- Determination of structural element for which the rate analysis is needed.

Learn More### CE2401-DESIGN OF REINFORCED CONCRETE AND BRICK MASONRY ...

water is to be 4m, including a free board of 200mm.Use M20 concrete. 15. An open rectangular tank 4m x 6m x 3m deep rests on firm ground. Design the tank. Use M20 mix. 16. Design an underground water tank 4m x 10m x 3m deep. The sub soil consist of sand having angle of repose of 30 degree and saturated unit weight of 17KN/m 3.The water

Learn More### Design for bolted structural joints

Steps must be taken to ensure that this information is conveyed to all those involved in installation, tightening, and inspection. Snug tightening When snug tightening is used as the first stage for full tightening in procedures 8.8/TF and 8.8/TB, the intention is …

Learn More